The brush bar of your Dyson DC25 vacuum is powered by a dedicated motor inside the cleaner head assembly. There has a rotary brush in your Dyson vacuum that spins at high speed and helps to beat and dislodge the dirt out of your floors. A type of angled bristles has also been used in your Dyson DC25 vacuum cleaner for sweeping and forcing the dust to be sucked into the hose. A motor that locates inside the vacuum cleaner move the bristles. It also enables your Dyson vacuum cleaner in vacuuming hard floors and upholstery more effectively. Sometimes, the brush bar on your DC25 may not be spinning for some basic reasons such as clogged or damaged brush bar, defective brush bar motor, faulty brush bar drive belt, etc.
Affiliate disclosure: As an Amazon associate, We'll earn a commission for every successful order through our affiliate links in the article. However, you won’t be charged anything for this.
Today, we are going to discuss some possible reasons about why your Dyson DC25 brush bar not spinning and how to get rid of this issue. Just keep reading this article.
Reasons Behind Dyson DC25 Brush Bar Spins Then Stops
Sometimes, your Dyson DC25 brush bar may not spin, or spins then stops due to operating the vacuum cleaner incorrectly. Such kinds of three major possibilities are given below that cause your Dyson DC25 brush bar may not spin:
- Dyson has designed their vacuum cleaners to lock into an upright position when not in use. The Dyson motor that spins the vacuum cleaner brush bar gets disengaged. In this case, simply depress the button locate near the cleaning head to unlock the handle. This tip may mobilize your Dyson DC25 vacuum again.
- If your Dyson DC25 cleaner is set too low, the brush bar may not work properly. Dyson vacuum usually comes with different height adjustments for cleaning several types of floors such as carpets, hardwood floors, tile floors, vinyl plank floors, etc. So, while using your Dyson vacuum cleaner make sure whether you’ve adjusted the cleaning height based on your floor type.
- Like other Dyson vacuum cleaners, your Dyson DC25 vacuum has a removable cleaner head. If the head isn’t locked into its exact position, the motor that supplies power to the brush bar may not spin. So, check whether the cleaner head has adjusted properly or not.
In this part, we will discuss three possible causes as to why the brush bar on your DC25 may not be turning. These are:
Clogged or Damaged Brush Bar
While cleaning your floor things like hair, fibers and threads can create clog around your Dyson brush bar that resists the brush bar from spinning.
To check whether your Dyson brush bar is clogged or damaged, simply rotate the bar with your hand. If it is tough to rotate with your hand, assume that this caused by a clogging issue. To clear them, you can use the following techniques.
First of all, disengage your Dyson DC25 vacuum cleaner from the plug and then lay it down on your floor to give you access to the brush bar. Next, simply remove the soleplate from your Dyson DC25 vacuum cleaner brush bar assembly. After that, cut hair, threads, and fibers with a pair of scissors that tangled with the brush bar, but while cutting those things you should be very careful to avoid cutting any bristles of the brush bar. Then detach your Dyson brush bar and pull it out in order to clean threads from the ends. And lastly, following the reverse way, reassemble the brush bar and cleaning head again. But if it gets damaged, you need to replace your Dyson DC25 brush bar with a new one.
Faulty Brush Bar Motor Assembly
There is a separate motor controlling brush bar in your Dyson DC25 vacuum cleaner located in the cleaner head itself. If this unit gets worst, you should better replace the entire cleaner head, as the motor is not available as a separate spare part.
Defective Brush Bar Drive Belt
In your Dyson vacuum cleaner, there remains a drive belt that is operated by the Dyson motor. If somehow the brush doesn’t operate correctly, your Dyson brush bar won’t spin. So, check whether the belt works correctly. If your Dyson DC25 brush belt gets damaged, you should replace it with a new one.
Final Words…
Since we’ve described the probable reasons and solutions about why your Dyson DC25 vacuum cleaner brush bar does not spin, now it will be pretty easy for you to detect the issue and solve it as well. Just follow our given advice. Thanks for staying with us.